Dissimilar Metal Joining of 304 Stainless Steel to SMA490BW Steel Using the Filler Metal Powders with a High-Entropy Design

Metals and Materials International - High-entropy alloys having excellent properties are particularly suitable for the application as the filler metals in welding. In the present study,...     

Up-pulling force analysis for ESC hollow cylindrical casting

Electroslag casting(ESC)is an important method to produce high quality castings.In this study,the ESC up-pulling inner mold method(EUPIM)was used to produce hollow cylindrical castings with the multiple consumable electrodes.The radial deformation,the axial and radial internal stress of the inner mold,and the axial internal stress of the slag shell were analyzed using the finite element method(FEM)with the aid of ANSYS software.The ProCAST software was used to calculate the specific heat,heat conductivity and density curve of Cu.Simulation results show that the radial deformation,the axial and radial internal stress of the inner mold,and the axial internal stress of the slag shell near the slag-metal interface of hollow cylndrical casting gradually increase from 0 s to 360 s after the ESC starting(slagging)process but before applying the up-pulling force.The suitable initial up-pulling moment of the inner mold is at around 180-198 s after the starting process.     

古建筑物维修用聚合物抗裂抹灰砂浆的配合比和性能研究

采用正交试验的方法,研究了胶砂比、胶凝材料组成、速凝剂掺量、胶粉掺量对一种修复古建筑物用聚合物抗裂抹灰砂浆的抗压强度、压折强度比、收缩率和拉伸黏结强度等性质的影响,并给出了性能优化的配合比。     

Thermodynamic and economic analyses of a coal and biomass indirect coupling power generation system

The coal and biomass coupling power generation technology is considered as a promising technology for energy conservation and emission reduction. In this paper, a novel coal and biomass indirect coupling system is proposed based on the technology of biomass gasification and co-combustion of coal and gasification gas. For the sake of comparison, a coal and biomass direct coupling system is also introduced based on the technology of co-combustion of coal and biomass. The process of the direct and the indirect coupling system is simulated. The thermodynamic and economic performances of two systems are analyzed and compared. The simulation indicates that the thermodynamic performance of the indirect coupling system is slightly worse, but the economic performance is better than that of the direct coupling system. When the blending ratio of biomass is 20%, the energy and exergy efficiencies of the indirect coupling system are 42.70% and 41.14%, the internal rate of return (IRR) and discounted payback period (DPP) of the system are 25.68% and 8.56 years. The price fluctuation of fuels and products has a great influence on the economic performance of the indirect coupling system. The environmental impact analysis indicates that the indirect coupling system can inhibit the propagation of NO_x and reduce the environmental cost.     

355 MPa级转向架构架用钢连续冷却转变行为

高速动车组转向架构架对高速动车组的运行品质、行车安全起到至关重要的作用。为向355 MPa级转向架构架用钢的工业试制提供指导，在Gleeble-3800热模拟试验机上进行了热模拟试验，结合热膨胀法和金相-硬度法，绘制了355 MPa级转向架构架用钢动态连续冷却转变曲线，研究了试验钢在连续冷却条件下的显微组织演变规律。结果表明，冷速小于1 ℃/s时，其组织主要为多边形铁素体和珠光体；冷速大于5 ℃/s时，贝氏体类组织快速增加；冷速达到50 ℃/s时，为板条贝氏体组织。因此，对于355 MPa级转向架构架用钢，冷速控制在1~5 ℃/s较为适宜，其组织主要由比例适中软硬性相结合的铁素体、珠光体和贝氏体构成，可以获得优良的强韧性匹配。     

微弧氧化Mg-3Al-1Zn镁合金应力腐蚀和腐蚀疲劳行为研究

本文主要对微弧氧化Mg-3Al-1Zn镁合金在空气和3.5 wt.%硫酸钠溶液两种环境下的应力腐蚀和腐蚀疲劳行为进行研究，并讨论其相互关系。微弧氧化处理后，Mg-3Al-1Zn镁合金的耐蚀性能得到明显改善。与Mg-3Al-1Zn镁合金基体相比，在空气中，微弧氧化后合金的应力腐蚀和腐蚀疲劳强度均下降了大约10 MPa。在3.5 wt.%硫酸钠溶液环境中，微弧氧化后合金的腐蚀疲劳性能仍然是恶化的，但是应力腐蚀强度却得到了显著改善，从58.24 MPa提高至202.08 MPa。这表明材料的力学性能（应力腐蚀和腐蚀疲劳）并不是与其腐蚀性能完全保持线性关系的。微弧氧化处理后镁合金在空气中的应力腐蚀断口为韧性断裂，在硫酸钠溶液环境中为解理断裂。而其腐蚀疲劳断口不论是在空气中还是在腐蚀环境中均为解理断裂。这主要是由于腐蚀环境和变换循环载荷的影响，两者共同作用将会加速裂纹扩展。这表明，周围环境和加载类型对材料断裂机理有重要影响。     

Ti-6Al-4V电弧熔丝增材轧制复合制造的有限元模拟

增材制造过程中由于在凝固及随后的冷却阶段易产生残余应力,从而影响部件的成形和使用。在增材过程中引入轧制工序,可望降低宏观残余应力,从而降低部件的变形。本文通过建立Ti-6Al-4V钛合金电弧熔丝增材与层间轧制复合成形过程的有限元模型,研究圆柱形轧辊条件下不同压下量对部件温度、应力、应变及残余应力分布的影响规律。结果表明,层间轧制可显著降低沉积层金属中的残余宏观应力；同时降低对基板的整体应力。采用圆柱形轧辊并增加压下量可显著降低宏观残余应力,还可以通过塑性变形改变材料的微观组织,提高材料性能,为复合增材工艺的优化指明了方向。     

热变形工艺对含硫非调质钢流变应力及组织的影响

在变形温度950~1150 ℃和应变速率0.01~5 s^-1下,通过Gleeble-3500热模拟试验机进行单道次压缩试验,研究了热变形工艺对含硫非调质钢F45MnVS流变应力及组织的影响。结果表明:随着应变速率的增大,热压缩过程中的峰值应力增加,随着温度的升高,峰值应力降低;动态再结晶平均晶粒尺寸随着应变速率、变形量的增加而减小,随着温度的提高而增大。     

纳米纤维素的疏水改性及应用研究进展

纳米纤维素作为一种性能优越的可再生纳米材料，应用前景极为广阔。然而，由于纳米纤维素结构上富含羟基，使其具有极强的亲水性，严重影响了纳米纤维素的疏水性能，并且在一定程度上限制了其在复合材料领域的应用。综述了纳米纤维素疏水改性的研究进展，从物理吸附、表面化学修饰（甲硅烷化、烷酰化、酯化等）、聚合物接枝共聚3个方面简述了目前应用较为广泛的疏水化改性方法，并对疏水纳米纤维素在包装材料、造纸、水净化等方面的应用现状进行了总结。最后对疏水改性纳米纤维素的未来发展进行了展望，旨在为疏水纳米纤维素的研究和应用提供参考。